Carbon capture and storage (CCS) is a relatively new technology to store pressurized carbon dioxide underground. One of the challenges is to keep pipelines and injection tubes safe and prevent corrosion. ²ÝÁñÉçÇø supports corrosion testing of metallic components and examines polymeric materials to reduce transport costs and avoid failure.

With the increased concern of carbon dioxide (CO2) on the environment, reducing carbon emissions into the atmosphere is now a major focus for most industrialized countries. Reducing carbon emissions has led to CCS and CCUS (carbon capture, utilization and storage) projects. The projects have predominately been in the USA and Canada for Enhanced Oil Recovery (EOR), but there is a growing demand in Europe, Asia and the Middle East.

Numerous global projects in the planning stage are operational as pilot, research, and development plants in most countries where CO2 is produced. Most CCS/CCUS projects aim to capture CO2 and store it below the surface, mainly in offshore locations.

Corrosion of CCS transportation pipelines

For metals used in the CCS/CCUS infrastructure, the corrosion or cracking of the carbon steel transportation pipelines and carbon steel or corrosion resistant alloy (CRA) injection tubing is the primary concern of potentially corrosive environment.

The risk of corrosion/cracking needs to be evaluated on a case-by-case basis since it’s severity will depend on the material and the specific levels of H2O, O2 and acidic gas impurities of CO, H2S, SOx, and NOx in the dense phase CO2.

In order to mitigate carbon steel corrosion in CCS transport pipelines, the use of corrosion inhibitors can be considered. However, their effectiveness would be dependent on the specific conditions, so would require qualification testing.

Corrosion Testing for CCS infrastructure may be required to evaluate the resistance of the materials to:

Testing polymeric materials

The main concerns in the use of polymeric materials for seals, linings, etc. in the CCUS infrastructure are:

The ²ÝÁñÉçÇø advantage

Our centers of excellence for the Energy sector are located in the US and Europe. The locations are fully equipped to perform corrosion testing and electrochemical testing on metallic components and polymeric materials used for CCS/CCUS infrastructure.

For more information about our corrosion testing services for CCS/CCUS projects, or request a quote, contact us today.

The primary sources of CO2 are coal and gas power plants, chemical plants (e.g., fertilizer production), oil refineries, and gas processing. In most CCS/CCUS projects, the CO2 is initially separated (captured), then compressed/processed and transported to the storage/usage location. The transported CO2 is either injected into existing producing oil wells for enhanced oil recovery (EOR) or injected into underground aquifers, salt caverns, porous rock formations, or depleted gas fields.

Compression/processing, transport, and injection operations must consider the impact of metallic componsents and the degradation of the polymeric materials.

For the corrosion of metals, the main factors to consider in the CO2 environment are water and gaseous impurities, in particular, O2, CO, H2S, SOx, and NOx. The processing of the CO2 is aimed at removing water and impurities; however, depending on the source of the CO2 low levels of water and impurities can remain in the transported gas. For transport and storage, to make the process economical, the CO2 is pressurized, which results in the CO2 gas phase being changed to a dense phase liquid or supercritical liquid. Any water within the dense phase CO2 will drop-out and will be acidic, with a pH of approximately 3, due to carbonic acid formation, from dissolved CO2. Other acidic species may also be present within the water phase resulting from the SOx and NOx impurities in particular.

Whitepaper: Rapid Gas Decompression (RGD) Tests Involving Hydrogen Sulfide

This white paper demonstrates that H2S is a more hostile gas than CO2 towards housed elastomeric seals subjected to repeated pressure cycling in RGD tests.

Read More

Understanding Mixed Flowing Gas Testing

Mixed flowing gas (MFG) testing is an accelerated aging test that specifically evaluates the corrosion of electrical components due to exposure to atmospheric gasses and contaminants.

Read More

Fracture Mechanics in Sour Service: Some Characterization Tests on SENT and SENB Specimen

This article provides better understanding of how the SENT test technique influences fracture toughness of pipelines in sour service environments.

Read More

Webinar: Corrosion of Stainless Steel

This webinar shows examples of corrosion damage and guides you through how to avoid corrosion in your stainless steel products to prevent product failure and costly repairs.

Watch Now
CASE STUDY

Emissions Monitoring on Carbon Capture Site

Read how our emissions team are using industry-leading instrumentation such as SIFT-MS to accurately measure the chemical composition of post-combustion flue gases at carbon capture plants.

Corrosion-Testing 640x480

Corrosion Testing Services 

Find out about ²ÝÁñÉçÇøs extensive corrosion testing expertise in the Energy industry across a global network of laboratories.

Read More
Mechanical Testing Services 640 x 480

Structural Testing & Mechanical Engineering

²ÝÁñÉçÇø offers a range of advanced and application oriented engineering services to help solve a wide variety of mechanical engineering and structural engineering analysis problems.

READ MORE
Coatings Testing

Coatings Testing

Find out about ²ÝÁñÉçÇøs range of coatings testing services designed to help to make certain that materials, products and pipelines we test for our customers are protected from corrosion, ultraviolet light, water penetration, heat, abrasion and chemicals.

read More
Materials Testing

Materials Testing

Find out more about ²ÝÁñÉçÇø's comprehensive ranges of materials testing services available in the TIC sector, covering materials selection, application and performance testing as well as failure analysis testing services.

Read More
Super Critical CO2 Testing with Sapphire Cell

Supercritical CO2 (scCO2)

²ÝÁñÉçÇø supports the energy industry in managing the challenges of polymeric materials like in service in supercritical CO2 (scCO2) environments.

READ MORE
Polymer-HPHT-640x480px

High Pressure High Temperature (HPHT) Exposure Testing Services

We offer extensive services for the qualification and compatibility of polymer materials exposed to production fluids at high pressure and high temperature (HPHT).

Read More
Polymer-Gas-Permeation-640x-480px

Permeation & Diffusion Testing

With a unique range of permeating capabilities for polymers, thermoplastics, elastomers and composites, we can simulate the high pressure and extreme temperatures found in deep wells, or the conditions in an automotive applications, utilities industry or chemical processing equipment.

Read More
Rapid Gas Decompression Testing (RGD)

Rapid Gas Decompression Testing (RGD)

²ÝÁñÉçÇø offers rapid gas decompression testing to help manufacturers and users of elastomers better understand the behavior of this material in true sour RGD conditions.

READ MORE

Our team of over 9,000 Engaged Experts in North America, Europe, The Middle East, Australia, Asia and Africa are ready to help you.